Just How to Replace a Tub
Schedule Your ServiceAre you in search of information about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably tough project. If the old bathtub is easily easily accessible, the project can relocate quickly; if you have to open up a wall to get rid of the old tub and position the new tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have certified yourself for the job as well as are comfortable trying it. Rather than working with a contractor to take control of a halfway-completed task, it is better to take into consideration employing one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This post will assist you install a new bath tub in your restroom if you have actually currently bought a new bathtub and do not require to alter the setup of your previous water supply pipelines.
Your devices and also material checklist must consist of the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last position.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, position the tub in the required placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub up until the level reads degree.
To set up faucets, fit all-time low of the furthest flexible faucet port to the ideal supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also inspect the overflow outlet as well as the normal outlet for leakages.
Finally, fix the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the bath tub ought to wait up until the bath tub has been utilized at the very least once as this will certainly settle it right into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former kind should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, creating the water to pass through the wall between the bathroom and also the tiling, leading to issues with wetness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes and also cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can break fairly early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Place a remark down the page. We will be glad to listen to your reactions about this write-up. We are looking forward that you visit us again before long. Make sure you take the time to share this content if you enjoyed it. We treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Instantly